Hi,
time for an updated post!
Now a bit simpler:
1. Inside the downloaded folder, you'll find screenshots for the settings and a txt-file with explanations
2. Drag&Drop the LUT you want to use. I recommend the RealNew80LUT to try first for everything apart from the DFGT
3. Set the gain in CM to the value that's in the name of the LUT. 80% for RealNew80LUT
Have fun
If your wheel is shaking a lot, if you want to customize a LUT or have any other question:
Simply post in the support thread and we'll get to it!
Important: the first 3 lines in the LUTs are the most important ones to get rid of the deadzone. If your wheel is shaking when standing still or vibrating too much:
Lower the first value for example (0|0.100) to (0|0.070).
This first value is NOT influenced by the overall ffb from the game so reducing Gain won't help!
The game ffb starts at the second value!
Hope this helps
Now for CM and Logitech settings:
DFGT/G25/G27:
G29/920/923:
900° and Sensitivity to 50%.
Here are the Settings again:
Important:
Un-Check "Car-specific controls" when selecting the car at the bottom left of CM. Otherwise, you might end up with different LUTs for different cars.
All settings as text:
AC Settings: [updated values!]
- Gain: Set to the value inside the LUT's name! (And 75-125% in the car, to make the center feel perfect for each car)
- Filter: 0
- Min Force: 0%
- kerb: 1-5% (unnecessary vibrations, Kerbs are real 3D in Assetto)
- road: 2-10% (5% is enough to give you some subtle vibrations on surface changes)
- slip: 23% (important to feel spinning or locking wheels!) 0% when drifting!!!!!!
- abs: 23%
- understeer: untick (unrealistic, only good for learning)
- Steering Settings: gamma 1, filter 0, sensivity 0!!
Experimental in CM or in:
[Assetto_corsa.ini:] (Not important!)
- DAMPER_MIN_LEVEL=0.0: This means, that the InGame dampening is OFF, when the Engine doesn't send damper signals. If you increase this settings, your dampening will ALWAYS BE ON, even if the engine does NOT give the input for it.
The G27 delivers already very few details so you don't want anything to be dampened!
- DAMPER_GAIN=0.0: I don't like it! It's this fake rubber effect. It's only active when standing still or slow rolling but it sounds awful with the Logitech wheels and is just annoying in my opinion.
It doesn't matter if you're adjusting the Damper slider in the Logitech Profiler or this setting. They scale the same effect.
Axis:
- Degrees: 900°
- Gamma: 1.0
- Scale: 100%
- Auto-adjust scale: off!
- Filter: 0%
- Speed Sensitivity: 0%!
- abs: 23%
CSP -> FFB Tweaks:
- Active: yes
- More physically accurate gyro: off
- Range compression: 100%! (more than 100% can feel great, but sadly it doesn't really work with the LUTs and your wheel will probably shake like crazy)
- Range compression assist: yes
- Custom soft lock:
- Active: yes
- Shift lock outside: 80%
- Speed factor: 100%
- Lock area: 15°
- Force factor: 100%
- Damper intensity: 0%
7. additional:
- Logitech Profiler:
- overall: 100 (don't raise this! you will get crazy rattling!)
- spring: 100 (doesn't do anything in AC)
- damper: 20-100 (only active while standing still and rolling slowly)
- untick center spring, NO combined pedals, 900° rotation, TICK "allow game to adjust settings"
Enjoy
time for an updated post!
Now a bit simpler:
1. Inside the downloaded folder, you'll find screenshots for the settings and a txt-file with explanations
2. Drag&Drop the LUT you want to use. I recommend the RealNew80LUT to try first for everything apart from the DFGT
3. Set the gain in CM to the value that's in the name of the LUT. 80% for RealNew80LUT
Have fun
If your wheel is shaking a lot, if you want to customize a LUT or have any other question:
Simply post in the support thread and we'll get to it!
Important: the first 3 lines in the LUTs are the most important ones to get rid of the deadzone. If your wheel is shaking when standing still or vibrating too much:
Lower the first value for example (0|0.100) to (0|0.070).
This first value is NOT influenced by the overall ffb from the game so reducing Gain won't help!
The game ffb starts at the second value!
Hope this helps
Now for CM and Logitech settings:
DFGT/G25/G27:
G29/920/923:
900° and Sensitivity to 50%.
Here are the Settings again:
Important:
Un-Check "Car-specific controls" when selecting the car at the bottom left of CM. Otherwise, you might end up with different LUTs for different cars.
1. Adjust InGame-settings and Profiler (ignore the NOT 900°... It's just to match the rotation of the real and visual wheel)
2. Open the controls.ini:
If you didn't edit this, you don't need to do this. We're just putting it back to defaults!
You find this ini in: "C:\Users\%username%\Documents\Assetto Corsa\cfg\controls.ini"
set MIN_FF=0.00, CENTER_BOOST_GAIN=0.0, CENTER_BOOST_RANGE=0.1 (range doesn't matter if gain=0.0)
3. open the assetto_corsa.ini:
Apart from the Damper_Gain, it's defaults here too!
You find this ini in: "%...%\SteamLibrary\steamapps\common\assettocorsa\system\cfg\assetto_corsa.ini"
set ENABLE_GYRO=0, DAMPER_MIN_LEVEL=0.0, DAMPER_GAIN=0.0
4. open the ff_post_process.ini
Now THIS is important! But in the zip folder I provided the files for easy drag&drop instead of editing manually!
You find this ini in: "C:\Users\%username%\Documents\Assetto Corsa\cfg\ff_post_process.ini"
set VERSION=1, TYPE=LUT, ENABLED=1, VALUE=1.0, Curve=%nameOfYourLutFile%
This enables the LUT. If the Value is NOT 1.0 the LUT won't work as it should!
5. put the LUT into the same folder as the ff_post_process.ini!
["C:\Users\%username%\Documents\Assetto Corsa\cfg\"
2. Open the controls.ini:
If you didn't edit this, you don't need to do this. We're just putting it back to defaults!
You find this ini in: "C:\Users\%username%\Documents\Assetto Corsa\cfg\controls.ini"
set MIN_FF=0.00, CENTER_BOOST_GAIN=0.0, CENTER_BOOST_RANGE=0.1 (range doesn't matter if gain=0.0)
3. open the assetto_corsa.ini:
Apart from the Damper_Gain, it's defaults here too!
You find this ini in: "%...%\SteamLibrary\steamapps\common\assettocorsa\system\cfg\assetto_corsa.ini"
set ENABLE_GYRO=0, DAMPER_MIN_LEVEL=0.0, DAMPER_GAIN=0.0
4. open the ff_post_process.ini
Now THIS is important! But in the zip folder I provided the files for easy drag&drop instead of editing manually!
You find this ini in: "C:\Users\%username%\Documents\Assetto Corsa\cfg\ff_post_process.ini"
set VERSION=1, TYPE=LUT, ENABLED=1, VALUE=1.0, Curve=%nameOfYourLutFile%
This enables the LUT. If the Value is NOT 1.0 the LUT won't work as it should!
5. put the LUT into the same folder as the ff_post_process.ini!
["C:\Users\%username%\Documents\Assetto Corsa\cfg\"
All settings as text:
AC Settings: [updated values!]
- Gain: Set to the value inside the LUT's name! (And 75-125% in the car, to make the center feel perfect for each car)
- Filter: 0
- Min Force: 0%
- kerb: 1-5% (unnecessary vibrations, Kerbs are real 3D in Assetto)
- road: 2-10% (5% is enough to give you some subtle vibrations on surface changes)
- slip: 23% (important to feel spinning or locking wheels!) 0% when drifting!!!!!!
- abs: 23%
- understeer: untick (unrealistic, only good for learning)
- Steering Settings: gamma 1, filter 0, sensivity 0!!
Experimental in CM or in:
[Assetto_corsa.ini:] (Not important!)
- DAMPER_MIN_LEVEL=0.0: This means, that the InGame dampening is OFF, when the Engine doesn't send damper signals. If you increase this settings, your dampening will ALWAYS BE ON, even if the engine does NOT give the input for it.
The G27 delivers already very few details so you don't want anything to be dampened!
- DAMPER_GAIN=0.0: I don't like it! It's this fake rubber effect. It's only active when standing still or slow rolling but it sounds awful with the Logitech wheels and is just annoying in my opinion.
It doesn't matter if you're adjusting the Damper slider in the Logitech Profiler or this setting. They scale the same effect.
Axis:
- Degrees: 900°
- Gamma: 1.0
- Scale: 100%
- Auto-adjust scale: off!
- Filter: 0%
- Speed Sensitivity: 0%!
- abs: 23%
CSP -> FFB Tweaks:
- Active: yes
- More physically accurate gyro: off
- Range compression: 100%! (more than 100% can feel great, but sadly it doesn't really work with the LUTs and your wheel will probably shake like crazy)
- Range compression assist: yes
- Custom soft lock:
- Active: yes
- Shift lock outside: 80%
- Speed factor: 100%
- Lock area: 15°
- Force factor: 100%
- Damper intensity: 0%
7. additional:
- Logitech Profiler:
- overall: 100 (don't raise this! you will get crazy rattling!)
- spring: 100 (doesn't do anything in AC)
- damper: 20-100 (only active while standing still and rolling slowly)
- untick center spring, NO combined pedals, 900° rotation, TICK "allow game to adjust settings"
Enjoy
You won't see if it's "on", but you will feel it. There's also a Steam Guide, just google for ACC LUT Steam and you should find it :)
My recommendations: Gain = 100% ; Min Force = 0% ; Damper = 0% ; Dynamic Damping = 0% ; Road Effects = 0-20% ; Frequency = default.
Steer Lock = 900° ; Linearity = 1.00 ; Brake Gamma to your liking ; Gearshift Debouncing = 50 ms (default).