The SimFeedback-AC DIY Motion Simulator thread

[sjb266]

Hey guys. Thought I’d create a thread for those taking the plunge into this brilliant DIY project..
I will be starting mine soon and I know there are others thinking about it.. so feel free to share your knowledge and experiences so we can all enjoy this platform to its full potential. A huge thanks to the developers who have really knocked this one out of the park!

Website: https://opensfx.com/2019/02/20/welcome-to-our-new-site/

Github: https://github.com/SimFeedback/SimFeedback-AC-Servo/wiki

For all the internals for the actuator contact Amy - skye@ntl-bearing.com
She can supply everything you need. Just remind her you want the ends of the shafts chamfered and make sure she sends the right sized ball screw - we have had a couple of issues reported. She is very helpful though and the cost is pretty good.


Huge thanks to @RowanH for writing a comprehensive user guide which can be accessed here - https://www.rowanhick.com/sfx-100-build-and-running-guide

In addition, @anton_Chez has contributed a list of post numbers for some of the important settings etc..
Post #320 SFX-100 thread
Post #327 SFX-100 thread for Discord correlation
Post #339 SFX-100 thread
Post #418 SFX-100 thread
Post #424 SFX-100 thread
Post #439 SFX-100 thread
Post #449 SFX-100 thread
Post #517 SFX-100 thread
Post #554 SFX-100 thread
Post #580 SFX-100 thread
Post #826 SFX-100 thread
Post #837 SFX-100 thread
Post #864,866,867,868,870,887,889,897 SFX-100 thread
Post #911,914 SFX-100 thread
Post #988,992,998 SFX-100 thread
Post #1147 SFX-100 thread
Post #1492 SFX-100 thread
Post #1511,1517 SFX-100 thread

I will try to keep this page updated with links to source the parts in other parts of the world. Just post whatever links you have and i'll add them here.

Please note: Not all the parts listed below are essential for the project. For the essential parts refer to the original shopping list.

Australia:

• O-Ring - https://www.ebay.com.au/itm/Kit-419Pcs-O-Ring-O-Ring-Black-Rubber-32-Sizes-With-Case-3-50mm-W8D7/223152697816?ssPageName=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649
• D-Sub breakout board - DB25 25pin Female Adapter RS-232 Serial Terminal Module Breakout Board Connector
• Emergency Stop - https://www.ebay.com.au/itm/Reliable-Emergency-Stop-Push-Button-Box-600V-Switch-for-Elevator/192115082001?ssPageName=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649
• Arduino Wiring - https://www.ebay.com.au/itm/40-pcs-Dupont-Cable-20cm-Jumper-Wire-for-Arduino-RPi-breadboard-AU-Stock/202436863098?ssPageName=STRK:MEBIDX:IT&var=502467628096&_trksid=p2057872.m2749.l2649
• Breadboard - https://www.ebay.com.au/itm/Mini-Solderless-Breadboard-400-Contacts-Tie-points-Universal-Available-New-lemon/123145741183?ssPageName=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649
• D-Dub Cable - https://www.ebay.com.au/itm/Black-D...h=item3f6ace6403:g:038AAOSw9mpaSsU2:rk:1:pf:0
• Screw Shield for Arduino Leonardo - https://www.ebay.com.au/itm/New-Scr...h=item25a9d471a4:g:5BgAAOSwraJbc9rC:rk:1:pf:0
• Arduino Leonardo Replica - https://www.ebay.com.au/itm/DIY-Eduino-Leonardo-Module-with-USB-Cable-for-Arduino-ATMEGA32U4-Blue-Black/132719951279?epid=916281063&hash=item1ee6b9bdaf:g:2QUAAOSw5iNbWv6b:rk:123f:

Thanks to @AussieSim for the following links:

10A power lead(s) * 4
https://www.jaycar.com.au/2m-black-mains-extension-lead/p/PS4152

Top quality wire stripper
https://sydneytools.com.au/product/boxo-cutws205-multifunction-wire-stripper

RCD/safety switch power block
https://www.bunnings.com.au/arlec-4-outlet-heavy-duty-portable-safety-switch_p4420028

WD-40 lithium grease for the ball screws
https://www.bunnings.com.au/wd-40-specialist-300g-high-performance-white-lithium-grease_p6100408

Vibration pads
https://www.bunnings.com.au/whites-on-site-100-x-12-5mm-rubber-anti-vibration-mat-4-pack_p3961547

WD-40 Dry PTFE spray for the slider (free shipping)
https://au.rs-online.com/mobile/p/lubricants/7577134/

Arduino Leonardo (free shipping + frequent 10-15% off discount)
https://www.arrow.com/en/products/a000057/arduino-corporation

DB25 cables * 4 (free shipping)
https://www.arrow.com/en/products/ak401-2/assmann-wsw-components-inc

PETG * 3 (free shipping)
https://www.arrow.com/en/products/petg17bk1/mg-chemicals

WAGO-like connectors to avoid a breadboard (perhaps use genuine ones if you are doing 240V AC)
https://www.aliexpress.com/item/32906719488.html

D-Sub breakout boards * 4
https://www.aliexpress.com/item/32297675967.html

3D printer Creality Ender-3 Pro
https://www.aliexpress.com/item/32918302452.html

Wires from Arduino to D-Sub breakout (remove black plastic from the WAGO end)
https://www.aliexpress.com/item/32887680826.html

Crimp connectors for AC wire leads
https://www.aliexpress.com/item/32813550981.html

 

[mouse1]

Hi,
I started to buy thing for this project. I'm just trying to order from Emily, but she didn't respond to my email since end of previous week. Am I using the right email address? emily@ntl-bearing.com

 

[anton_Chez]

Looks like the one however I am unsure if the formatting is exactly how you have it, let me check.

 

[anton_Chez]

Looks like the one however I am unsure if the formatting is exactly how you have it, let me check.

‎<emily@ntl-bearing.com>

 

[anton_Chez]

Triple post damn internet.

 

[Mascot]

Triple post damn internet.

inb4 "check you haven't installed your router upside down"

 

[anton_Chez]

It's not meant to be that way..........?

 

[anton_Chez]

My belt tensioner with RC Servos works damngood ... Costs .. 100 Euro (inspiration: SeatTime)

Did you build this yourself, Jochen? I am searching for my own alternative. There is a guy here in Australia that builds these but I am unsure when they will be available again and the cost is going to run me around $600 AUD.

 

[mouse1]

Hmm, it seems, I tried the right email address. Ok, maybe spam filter kicked in. Let me try her Skype address...

 

[saxxon66]

@anton_Chez Jochen and me worked together on this RC-Servo seatbelt project.
You can find the build thread here.

https://forum.virtualracing.org/sho...ffer-100-Euro-(auch-Ohne-Motion-realisierbar)

I am using it on my rig.

It is working ok, not the strongest motors and sometimes noisy, but anyway.

 

[C64]

@anton_Chez Jochen and me worked together on this RC-Servo seatbelt project.
You can find the build thread here.

https://forum.virtualracing.org/sho...ffer-100-Euro-(auch-Ohne-Motion-realisierbar)

I am using it on my rig.

It is working ok, not the strongest motors and sometimes noisy, but anyway.

So Michael... if I held a gun to your head and asked you to choose between 1.seat belt tensioner and 2.rear traction loss ... would your answer be 1 or 2

 

[anton_Chez]

No guns please, we need him!

 

[saxxon66]

For me? None of both.

Wait, wait, wait, don't shoot! let me explain

The seat belt tensioner is a nice add on, but it is realy inconvenient. So much hassle to put on and off each time. So most if the time I am not using it.

Traction loss, I do not have much experience with it, I tried it only once.
It was hard for me to detect at all, I'm not sure if it was a settings thing or this particularly mechanic.
Maybe I'm not sensitive enough for these kind of motions.

But keep in mind, these are only my personal preferences and experiences.
I do know guys who love their seat belt tensioner and traction loss.

 

[Moxley6969]

Traction loss when setup properly and Not Super sensitive so that you feel the TL axis EVERY time you breath on the steering wheel is IMO a No questions asked kind of affair.

Like adding motion as a whole. Once you got it, There's no going back.

@saxxon66 Strange, After a few years of wearing belts, It feels awkward Not to wear the belts while in the hot seat.

I guess were all different and have unique preferences.

If you did you belts all over, would you opt for bigger motor's...or stick with the Servos ?

 

[AlexP37]

Does anyone have a logo for the SFX-100 that they can share? I know @sjb266 printed one for his control box. I am having a car skinned for my upcoming V8 Supercars season and I want to replace the Nvidia logo on the back with the SFX-100 logo.

I’m working on it as we speak, a 3d printable one.

Dont know when its done though, busy with work and my kids.

 

[AlexP37]

For me? None of both.

Wait, wait, wait, don't shoot! let me explain

The seat belt tensioner is a nice add on, but it is realy inconvenient. So much hassle to put on and off each time. So most if the time I am not using it.

Traction loss, I do not have much experience with it, I tried it only once.
It was hard for me to detect at all, I'm not sure if it was a settings thing or this particularly mechanic.
Maybe I'm not sensitive enough for these kind of motions.

But keep in mind, these are only my personal preferences and experiences.
I do know guys who love their seat belt tensioner and traction loss.

Would it be possible to share your seatbelt tensioner build ?

I would like the same thing as the one shown in the sfx-100 build/explanation videos from florentin.

 

[HoiHman]

I just ordered the parts for the DIY seatbelt tensioner and have opened a topic here:
https://www.racedepartment.com/threads/diy-seatbelt-tensioner-with-simtools.163727/

 

[MADShootStuff]

Ok, I think I worked out the email issue I was having with Kinetik.

It looks like since the website update they're using a different domain for email so this address seems to be working:
info@haec-aluminium.de

That still leaves my package in Hamburg for 5 weeks but at least I may be able to get a response now!

 

[primi]

Thanks sjb266! You guys are all great and so responsive!

I'm glad it's working for you. Many days and countless posts later my post is still not worthy of a reply. Perhaps it contained stupid questions but more likely people noticed and thought "I can't be bothered but surely somebody else will deal with that." Not a great first impression. So I guess I'll be out of this place, down the road wherever...

 

[TimothyDDX]

Can anyone confirm that the reduction bushing/thread insert here is the same as the one on the shopping list but the part number changed for the hyperlink? It says "Reducing sleeve RH10 / M8, material: steel, galvanized" which looks to be the same as the old one, but want to confirm before I order.

Old part (broken link): http://kinetikmsystem.de/Aluprofil-...--klemmverbinder-/Reduzierhuelse-RH10-M8.html

New Part: https://www.kinetikmsystem.de/de/pr...eduzierhuelse-rh10/m8-material-stahl-verzinkt

 

[dedraro]

Hi guys, I'm starting this adventure too, thank you saxxon66