Cars (DATA REPLACEMENT) Mazda RX-7 FD3S Improved Physics by Arch

[Kyuubeey]

Kyuubeey updated (DATA REPLACEMENT) Mazda RX-7 FD3S Improved Physics by Arch with a new update entry:

Tuned versions, FFB changes

15.06.2019 Version 1.4

- Weaker FFB to represent 1999+ powersteering changes
- S3 tire size changed from 255/255 to 265/265
- Added negative preload possibility to S3 ie: OS Giken
- Changed S3 springs from 22/20 to 18/18
- Changed S3 differential settings
- Changed S3 alignment
- Raised S3 front 10mm
- Changed S2, S3 dampers knee

Read the rest of this update entry...

 

[Kyuubeey]

Kyuubeey updated (DATA REPLACEMENT) Mazda RX-7 FD3S Improved Physics by Arch with a new update entry:

Motion ratios, setups

22.07.2019 Version 1.5

- Front motion ratio 0.630 -> 0.671 as per HKS
- Rear motion ratio 0.750 -> 0.714 as per HKS
- Default setups changed for tuned cars
- Geometry adjustments to tuned cars; rear LCA from adjusted to un-adjusted
- Rear bushing deflection added to S1 and S2; far less due to stiffer bushing
- S3 tire stiffness changed
- New tire camber values

Read the rest of this update entry...

 

[Kyuubeey]

Kyuubeey updated (DATA REPLACEMENT) Mazda RX-7 FD3S Improved Physics by Arch with a new update entry:

Increased S3 rear downforce

26.07.2019 Version 1.5b

- Increased downforce and drag of S3 rear aerofoils to more realistic level

Read the rest of this update entry...

 

[IBurnDownTreez]

Hey man. I downloaded the mods and followed the instructions listed to a T but for some reason the cars wont load onto the track. I have them available for selection in the garage page but no matter which one I pick none will work. i can't even get them to work in the CM. Please help LOL

 

[Leonardo Ratafiá]

Hey man. I downloaded the mods and followed the instructions listed to a T but for some reason the cars wont load onto the track. I have them available for selection in the garage page but no matter which one I pick none will work. i can't even get them to work in the CM. Please help LOL

try Replacing sound with the Kunos RX7. sometimes is just that

 

[Kyuubeey]

Hey man. I downloaded the mods and followed the instructions listed to a T but for some reason the cars wont load onto the track. I have them available for selection in the garage page but no matter which one I pick none will work. i can't even get them to work in the CM. Please help LOL

It's almost always what Leonardo said. Try the Replace sound function.

 

[Kyuubeey]

Kyuubeey updated (DATA REPLACEMENT) Mazda RX-7 FD3S Improved Physics by Arch with a new update entry:

S4 version, wing config, minor changes

10.08.2019 Version 1.6

- Added S4 version
- Added wing 3D replacement model and config by @Trawa#3727
- Changed S3 turbo and power.lut slightly
- Changed engine inertia, limiter hz in S3
- Some minor tire changes

Read the rest of this update entry...

 

[Amir Vodokotlic]

How do I drive the S4?

It wants to kill you at any time it hits boost.

Going straight even in 4 gear rear end gets loose as soon boost is hit.

I noticed in setup diff preload is -120 Nm is that normal?

 

[Kyuubeey]

How do I drive the S4?

It wants to kill you at any time it hits boost.

Going straight even in 4 gear rear end gets loose as soon boost is hit.

I noticed in setup diff preload is -120 Nm is that normal?

Half-throttle technique. You ease it past boost. It's making 800ps+ at crank, it's a lot.

Yeah, negative preload differential, like an OS Giken unit. Added in as option because I like them.

 

[Błażej Wianecki]

S3 and S4 fail to load for me :/ I use the usual technique. I also replaced the sound via CM. Strange.

 

[Kyuubeey]

S3 and S4 fail to load for me :/ I use the usual technique. I also replaced the sound via CM. Strange.

You're probably not using the KS RX7 Tuned, but the Spirit R .kn5.

 

[Błażej Wianecki]

Well, no, it's not the case unfortunately. Nevermind, I'll look further.

 

[Kyuubeey]

Well, no, it's not the case unfortunately. Nevermind, I'll look further.

I suggest just doing it from the beginning. Should work if you do it literally step by step.

 

[Leonardo Ratafiá]

Well, no, it's not the case unfortunately. Nevermind, I'll look further.

You also need latest CSP version

 

[kevink63]

Thanks for your work. Really nice.

Just a note, though- I can't seem to get the S3 and S4 to load for some reason. It comes up with an error for both, pictured in thumbnail below.



Any help or suggestions would be greatly appreciated.

 

[Kyuubeey]

Thanks for your work. Really nice.

Just a note, though- I can't seem to get the S3 and S4 to load for some reason. It comes up with an error for both, pictured in thumbnail below.

View attachment 319684

Any help or suggestions would be greatly appreciated.

The error spells it out clear. You're probably using with with KS Spirit R visuals, not the KS Tuned visuals which I outlined in the installation guide.

 

[Leonardo Ratafiá]

 

[kevink63]

The error spells it out clear. You're probably using with with KS Spirit R visuals, not the KS Tuned visuals which I outlined in the installation guide.

Awesome, got it working. Thanks for the help and your awesome work.

 

[Kyuubeey]

Kyuubeey updated (DATA REPLACEMENT) Mazda RX-7 FD3S Improved Physics by Arch with a new update entry:

Geometries, brakes

27.08.2019 Version 1.7

- Changed front and rear geometry, a bit closer
- Changed brakes, EBD

Read the rest of this update entry...

 

[cherylleam]

.