Hi. This is my Ferrari 488 gt3 wheel replica I made for Russian simracing community.
So, wheel features:
307mm diameter
1180g or 1414g weight (with Thrustmaster quick release or 6x70mm aluminium adapter respectively)
5mm carbon fiber front plate
Injection molded rubber grips
Injection molded...
Hi All,
First post on these forums but wanted to share my lockdown project! Hopefully will get round to posting pictures when I dig them out on my PC.
My friends and I have been watching F1 for a few years, and when lockdown put a halt to both the F1 and the joy of going to the pub to watch...
Dear All,
welcome to my rig report - i have some interesting stories and projects to share
all my projects are shared via thingiverse - for your private usage
https://www.thingiverse.com/pwistudio/designss
after some intro pictures you will find my chapter structure to see my important posts...
Hello !
I build a complete static paddles for Fanatec wheelbases, including the electronics needed to connect the paddles to the SHIFTER2 port. The main advantage of this project is that you can design your own sequential shifter and plug it into the base directly, avoiding using a...
I am in the process of building a DIY wheel that I would like to be able to attach to a DD1 base via a Podium hub. As far as the physical wheel I have it all planned out as to how it will attach to the hub. What I am a bit lost on is what board/boards I will need to enable the buttons and...
Hejhej,
I was planning my projekt for my new Racing Wheel and I stumbled over the following sentence on SimHub Wiki:
"Arduino Pro Micro : The arduino will emulate a TTL and allow RGB LEDs or buttons to be added"
Now, I plan to add rgb leds AND buttons and I am wondering, if every free pin is...
Hey guys, I´d like to show you my latest simracing project. In the last few weeks I got back into I Racing and decided to race in the ILMS Series with the Ford GTE. Because my BMW M4 DTM rim kinda broke lately, mostly bc of too many loose wires inside it, I decided to make a new rim for myself...
After finally switching to the great Clubsport V3's i have discovered this annoying problem where the clutch makes a rather loud "clunk" when it's fully compressed. It's not a design flaw by any means, but in my setup my neighbor on the other side of the wall can hear it, and it's understandably...
Hello everyone,
So recently, since I have a lot of free time I got an idea to make a formula steering wheel for my g29.
The problem occurs when it comes to wiring all the buttons and encoders.
At the begining I wanted to use one of Arduino boards since they are quite cheap.
But when I did some...
Hey guys,
I have a question about the Accuforce DIY Steering KIT: https://www.simxperience.com/products/accessories/accuforcesteering/accuforcewheeldiykit.aspx
On there website they say, that this is not a ready to race and a DIY kit. So do I just need to buy a Wheel...
My final lockdown project after the bass shaker and handbrake was a proper sequential shifter.
I already had the TH8A shifter but i didn't want to keep changing it between H-pattern and sequential, plus there is no tactile 'clunk' in its sequential action.
Of course, the thrustmaster TSS...
My second lockdown project after the bass shaker, and in honour of getting dirt 2.0 as a freebie on PS4 I wanted to get a handbrake as i didn't like pressing a button on the wheel face.
I wanted a thrustmaster TSS but couldn't justify the price, plus if i wanted a handbrake and sequential...
Thought I'd use this lockdown time for a few projects on my very simple racing rig (PS4, T300RS, playseat challenge).
The first was a tactile transducer / bass shaker. I had seen the buttkicker gamer 2 but it seems permanently out of stock and i didn't want to spend £230 on it either.
I...
Hi, I have a Logitech g29 with a DIY steering wheel, is it possible on "Assetto Corsa Competizione" to combine keyboard commands (for the DIY steering wheel) using at the same time pedals and motor of the Logitech?
I've made a DIY pedal set to replace T3PA pedals from Thrustmaster.
The aim here is to achieve a better feeling (heavier pedals overall) while keeping the cost as low as possible. I've used a technical info from Heusinkveld pedals as a reference.
CAD files can be downloaded HERE
This is an Arduino Based 5.0" Capacitive Touch display with 16 RGB LEDs for Sim Racing. The enclosure is 3D printed in PLA.
The display is a Buy Display based on the RA8875 driver communicating it with the Arduino with 4 Wire SPI protocol for the graphics and with I2C for the touch panel.
It...
I've been looking around for a way to mount my phone, used a dash, where I could see it clearly but have it integrated with my wheel and base. I've looked at and came close to purchasing a pre-made unit for anywhere between $50 and $80. This is what I came up with for $9 and change and about...
hello this is my first post here
i just bought all the required parts to build my own diy FFb wheel
part list :
stm32f4 discovery
h-bridge bts7960
printer encoder from canon ip1800
dc motor
and 12v power supply
can any one hellp me with wiring please i've been trying to do it for 3 days but no...
Hi,
when I tried to loosen the nuts on my Simucube 2 Pro the head of the bolt literally snapped off. To me it felt like the Bolt was a lot tighter then when I installed it (Maybe the vibration somehow jammed the thing?). Has anyone here encountered a similar problem ?